In a house built of wood, you can buildwiring in almost any way. However, in recent years, designers are choosing a retro style. After all, this method has several advantages. First, this is a good way to organize electricity in the house. Secondly, the wiring, laid in this way, as much as possible emphasizes the retro style throughout the interior.
What is retro-wiring? Photos help answer the question. This method of installing an electrical cable in the last century was considered the only one. However, after a while the wires began to be stacked in special boxes - channels, or strobes. Posting in a retro style was rarely used. Most often, this type of installation is used only to emphasize the originality of the interior. Recently, many manufacturers have started to produce a whole series of twisted fittings.
Today, consumers have the opportunitypurchase television, telephone and electrical cables, chandeliers, sockets and junction boxes, made in the style of the last century. It should be noted that for their creation, mainly use porcelain, electrical engineering plastic, brass and copper.
Most of the country cottages, where applicableThis method of laying the electric cable, saturated with lighting devices and a variety of energy-intensive household appliances. That's why when installing, you need to use copper wires (when laying to chandeliers and lamps) with an enlarged section (up to 1.5 mm²), and for powering outlets - up to 2.5 mm².
It is worth noting that the retro-wiring in the woodenthe house does not hide in the walls. This is strictly prohibited. This fact is due to the fire safety of the entire building. Twisted wiring in the house allows you to solve many problems. The cables practically do not contact the wall surface. In this case, all sockets, as well as switches must be invoiced.
Wiring retro stylePerform at a distance of 10 mm from the wall surface. Fires are most likely to occur due to a lack of normal wire contact in the junction box. That's why every cable should be well fixed. For this purpose, it is best to use special terminals. With regard to junction boxes, it is better to install them in an easily accessible place.
Mounted similar electrical wiring in the house is notonly from wood, but also bricks. In this case, it is best to fasten the rollers with dowels. When screwing the screw, the sleeve is wedged. This element has a fibrous structure. Therefore, during installation there are no problems.
The wiring harness usually consists of two or threelived. Its choice depends on the presence of grounding. After and before the insulator, before attaching to the cable, you should put on pieces of heat shrinkable tubing, which will ideally match the color. This precaution will make the fastening more reliable. Retro-wiring in a wooden house must comply with all fire safety rules. As for the cable, it must be certified for laying open wiring.
Roller for fixing the cable is better to fixwood screws. When installing the cable, you should install porcelain insulators at each switch and outlet. Place them at a distance of 5 cm from each electrical point. Rollers must be fastened on the wire line with intervals of 0.5 meters, and on bends - 0.45 meters, and also at an angle of 45 °. To connect the cable in the junction box, it is necessary to use the terminal blocks for the flexible wire.
If the retro-wiring in the wooden house is open,then the corrugated tube can not be used. However, it is worth considering that a cable with a large cross-section in this style is not manufactured. Therefore, he is unlikely to fit into the overall interior. In this case, it can be hidden in the corrugated pipe. If in some places the laying of the wiring is carried out in hidden channels, then a special cable with an appropriate fire safety index should be used.
Also, wires designed for energy-intensivedevices, it is necessary to stack in a corrugated tube. For these purposes, you can use a conventional plastic cable duct, which is the most suitable for color. It is not uncommon for retro-wiring in a wooden house to be laid only on areas that are visible to the eye. This allows you to save money.
Installation of retro style wiring in a wooden house is carried out in several stages.
Installation of retro-wiring will not cause largedifficulties, if you comply with all the rules. As a result, a good addition to the basic style of the interior is obtained. If you use the raw materials for retro-wiring that meet all the requirements, then you can not be afraid of a sudden fire.
</ p>
